DeVilbiss 306DS Specifications download pdf (Page 10)

10 A-306

OPERATION

Initial Battery Operation

The new battery packaged with your iGo Portable Oxygen System is not fully charged. Before using your iGo for the ﬁrst time, you must install and

fully charge the battery.

1. Connect the AC Power Cord and plug in to completely charge the battery. This may require up to 4.5 hours of uninterrupted charging.

In the event of a power interruption, the iGo Portable Oxygen System will automatically switch to the battery operation if installed. When AC

power is restored, the battery will automatically start recharging. If the battery is not present during a power interruption, the Power Fail alert will

activate and the iGo will stop operation. When power is restored, unit will resume oxygen production unless the Power Button was pressed to

stop the Power Fail Alert.

Typical Battery Recharge Time

The typical time to recharge your battery from a fully discharged condition is 2.0 hours to 4.5 hours dependent upon the ﬂow setting. If the Battery

is too warm, charging will not begin until it sufﬁciently cools. Extreme temperature (high or low) may extend charge time.

oPeRaTInG YoUR IGo

WARNING

Do not leave iGo running when not in use� Do not leave cannula unattended while unit is delivering oxygen� High concentrations of

oxygen can cause rapid burning� Keep the equipment in a well-ventilated area�

1. Check to see if the air ﬁlter is in place before using. If the air ﬁlter needs to be cleaned, wash with soapy water and allow to dry before using.

If necessary, replace with a new air ﬁlter.

2. Plug unit into AC Power, DC Power, or make sure there is a charged Battery installed.

NOTE–Every time a button is pressed or when a change to the power source occurs, the iGo will give a short audible chirp.

3. Connect the tubing to the oxygen outlet and the cannula.

DANGER

If tubing becomes disconnected during operation, iGo does not alert� Check flow at the cannula to verify oxygen delivery�

4. Attach a standard nasal cannula to the oxygen outlet and to your nose and face. Breathe normally through the cannula.

CAUTION– Toensurethereisadequateowtodeliveroxygen,thelengthofthetubingmustnotexceed50feet(15.2m)when

usingContinuousFlowMode,andmustnotexceed35feet(10.5m)whenoperatinginPulseDoseModeforadequate

breath detection.

5. Press and hold the Power Button to turn your iGo On. When the unit is turned On, all the lights on the control panel will illuminate brieﬂy and

audible alert will brieﬂy activate.

a. When using External Power:

1) In PulseDose mode: After a few seconds, the External Power, Normal Oxygen, and Flow Rate lights will remain lit. The Flow Indicator

Light will pulse with each breath. If a battery is installed, the Battery Status Lights will either illuminate indicating battery charge level

or cycle indicating battery is charging.

2) In Continuous Flow mode: After a few seconds, the External Power, Normal Oxygen, Flow Indicator, and Flow Rate lights will remain

lit. If a battery is installed, the Battery Status Lights will either illuminate indicating battery charge level or cycle indicating battery is

charging.

b. When using Battery Power:

1) In PulseDose mode: After a few seconds, the Normal Oxygen and Flow Rate lights will remain lit. The Battery Status Gauge Lights will

also be lit indicating battery charge level. The Flow Indicator Light will pulse with each breath.

2) In Continuous Flow mode: After a few seconds, the Normal Oxygen, Flow Rate, and Flow Indicator lights will remain lit. The Battery

Status Gauge Lights will also be lit indicating battery charge level.

NOTE– The DeVilbiss iGo has an oxygen sensing device (OSD) to monitor oxygen purity once the oxygen stabilization process is

complete(afterapproximatelytherst20minutesofoperation).Oncestabilized,theOSDmonitorstheoxygenpurityandwill

alert if purity falls below an acceptable level.

6. To change your Delivery Mode, press the Mode Select button. The iGo will come on at the last mode and ﬂow setting used.

a. Continuous Flow Operation - When operating in Continuous Flow Mode, a continuous supply of oxygen will ﬂow through your tubing

and nasal cannula.

b. PulseDose Operation - When operating in PulseDose mode, an alert will beep after 30 seconds if a breath is not detected. If another 60

seconds elapses and no breath is detected, the unit will switch to Continuous Flow at the last Continuous Flow setting used.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

DeVilbiss 306DS Specifications Page 10

Comments to this Manuals

Related products and manuals for Oxygen Equipment DeVilbiss 306DS